If you’re wondering how to remove algae from paths, it’s worth understanding why the green growth appears in the first place.
Algae can develop on paths, paving, concrete, steps and other exterior surfaces, particularly where conditions are damp or shaded.
Apart from making an otherwise clean property look neglected, algae can also contribute to a slippery surface when wet, creating a potential slip hazard on frequently used pedestrian areas.
The good news is that algae can be treated effectively — but simply blasting away the green colour may not always provide the best long-term solution.
Why Does Algae Grow on Paths?
Algae thrives in damp conditions.
Paths that receive limited sunlight, remain wet for long periods or are surrounded by vegetation can be particularly susceptible.
This is why green growth is often most noticeable on shaded pathways, steps and entrances, concrete and paving, areas beside walls and buildings, paths beneath trees and vegetation, north-facing surfaces and areas where water drains slowly.
Ireland’s relatively damp climate can make exterior surfaces particularly susceptible to recurring biological growth.
Is Algae on a Path a Slip Hazard?
It can be.
As algae develops on a path, the surface can become slippery, particularly when wet. This means the problem isn’t necessarily just cosmetic.
Extra attention should be given to pedestrian areas such as entrances, steps, ramps, paths and frequently used access routes.
Regular inspection allows growth to be identified and treated before it becomes more established.
The Health and Safety Authority (HSA) also provides guidance for workplaces on preventing slips and trips, including the importance of suitable cleaning and maintenance.
Does Pressure Washing Remove Algae?
Pressure washing can produce an impressive immediate result because it physically removes visible contamination from the surface.
However, if the conditions that encourage algae remain, the green growth can return.
High-pressure cleaning may also be unsuitable for some surfaces, particularly where aggressive cleaning could damage joints, coatings or the surface itself.
Where algae is the underlying problem, using an appropriate algae treatment provides a more targeted approach.
How to Remove Algae From Paths
For established algae growth, Wilton Technology supplies Algae Remover (technical name Roloxid 10) for treating suitable exterior surfaces.
The process is straightforward:
1. Inspect the surface
Determine the extent of the algae growth and make sure the surface is suitable for treatment.
2. Choose the appropriate dilution
Depending on the degree of growth, dilute Algae Remover between 1:5 and 1:20, following the current product label and manufacturer’s directions.
3. Apply the solution
The diluted product can be applied using a knapsack sprayer or watering can, giving the affected surface a good wetting.
4. Check the weather
Apply when no rain is expected for approximately 8–9 hours, allowing sufficient time for the treatment to work.
5. Allow the treatment to work
The algae should begin turning brown within a day or two and should be dead within approximately a week. Subsequent weathering can then gradually remove the remaining dead material.
Always read the current product label and follow the manufacturer’s directions before use. Use the appropriate PPE and consider the surface and surrounding area before application.
How Much Area Will Algae Remover Cover?
Coverage depends on the dilution used and the condition of the surface.
As a guide, one litre of concentrate can treat approximately:
At 1:5 dilution — up to 50m²
At 1:20 dilution — up to 200m²
Actual coverage will depend on factors including the application method, surface porosity and amount of solution applied.
What Surfaces Can Be Treated?
Wilton Technology’s Algae Remover can be used on a range of suitable exterior surfaces, including concrete, pathways, tarmacadam drives, timber decking, tiles, playground surfaces, tennis courts, headstones, sandstone, metal, roofs and uPVC.
Always check the current product instructions and surface suitability before application.
How Can I Stop Algae Coming Back?
There isn’t a single permanent solution because the environmental conditions that encourage growth — particularly moisture and shade — may remain.
Regular inspection and appropriate treatment can, however, help control the problem.
Pay particular attention to areas that remain damp, receive little sunlight or have experienced algae growth previously.
Should I Pressure Wash or Treat the Algae?
The two methods perform different jobs.
Pressure washing is primarily a physical cleaning process that can rapidly improve the appearance of a dirty surface.
An appropriate algae treatment is intended to treat the biological growth itself.
The most suitable approach therefore depends on the surface, its condition and what you’re trying to achieve.
For more information, read our guide on why algae can come back after pressure washing.
When Is the Best Time to Remove Algae From Paths?
Rather than waiting until paths become heavily covered, inspect exterior surfaces regularly.
Choose a suitable period of dry weather so the treatment has adequate time on the surface without being washed away by rain.
Autumn and other wet periods are particularly important times to monitor pedestrian areas because pathways, steps and entrances can remain damp for longer.
Need Advice on How to Remove Algae From Paths?
If you’re unsure which treatment or dilution is appropriate for your particular surface, speak to us before application.
Wilton Technology supplies professional cleaning and hygiene products to customers in Cork, Munster and throughout Ireland.
Our Algae Remover (Roloxid 10) is available for treating algae on paths and a wide range of other suitable exterior surfaces.
Wilton Technology – Cleaning & Hygiene Supplies
Tel: 021 4810688
Email: sales@wiltontech.ie
Contact us for advice or to enquire about Algae Remover.

